Floor fire damper installation guide

The installation of fire dampers in line with these separating elements creates a passive barrier that will activate in the event of a fire and prevent the At Hydro-X Fire, not only can we complete the fire damper installation and replacement, but we can also assist with the following fire damper services 1. Type of Wall & Damper Orientation Dampers are to be installed vertically in masonry walls or gypsum / steel stud walls or horizontally in floors. Sleeve gauge requirements are listed in the SMACNA Fire, Smoke and Radiation Damper Installation Guide for HVAC Systems and in NFPA90A. Fire Damper. INSTALLATDIaOmNpeIrNs S- TTyRpUe CB TAInOdNCS -Typical. SLEEVE. 2. Reference the damper's installation instructions regarding the approved method of attaching the Fire damper and sleeve assemblies must be installed in wall and floor openings using retaining RE: Fire Dampers installation detail. AnotherEllis(Mechanical) 24 Dec 10 16:36. OK, so I assume you are using a dynamic type FD, a Ruskin D1BD2 or Sleeve gage requirements are listed in the SMACNA Fire, Smoke and Radiation Damper Installation Guide for HVAC Systems and in NFPA90A. This Installation Instruction applies to Fire Dampers (static curtain type) mounted in the plane of an UL approved fire partition. Important General Notes: 1. The dampers are designed for operation in the vertical or horizontal position with blades running horizontal. 2. The dampers are to be installed Fire dampers are passive fire protection products used in heating, ventilation, and air conditioning (HVAC) ducts to prevent the spread of fire inside the ductwork through fire-resistance rated walls and floors. Q: Do you need a fire smoke damper at floor level in an open duct shaft? Or where the duct comes out through the shaft wall? A: Section 19.7.5.1 of the 2000 edition of the Life Safety Code requires compliance with section 9.2. Section 9.2.1 requires compliance with NFPA 90A Installation of Air 4. Damper Orientation Damper is designed to operate with blades running horizontally and must be installed with center line of damper frame within the wall or floor when they are in the closed These connections are de-picted in the SMACNA Fire, Smoke, and Radiation Damper Installation Guide. Inspect installed damper for proper orientation, as stated. The basic inient of a proper installation is to secure such manner as to prevent distortion and disruption of The opening in the wall or floor for the fire damper shall be sized so as to provide expansion clearance between the sleeve and opening. These installation instructions apply to Fire Dampers of the stat-ic, dynamic, curtain-style, single and multi-blade types mounted in the plane of a UL* approved fire partition. For dampers needed to be installed outside the plane of a UL approved wall or floor, refer to the Out of Wall Fire and OW fire dampers may be used for through penetrations or duct terminations where the damper cannot be installed within the wall or floor. Sleeve gage requirements are listed in the SMAC-NA Fire, Smoke and Radiation Damper Installation Guide for HVAC Systems and in NFPA90A. OW fire dampers may be used for through penetrations or duct terminations where the damper cannot be installed within the wall or floor. Sleeve gage requirements are listed in the SMAC-NA Fire, Smoke and Radiation Damper Installation Guide for HVAC Systems and in NFPA90A. Safe-Air Dowcos installation notes are applicable to fire dampers, smoke dampers and combination dampers on most occasions. E. EXPANSION SPACE A. DAMPER ATTACHMENT TO SLEEVE a. Fire Damper Sleeve Clearance within Wall/Floor Opening a. Secure damper to sleeve on 8 (203) Supplementary installation instructions optional sealing of fire dampers and combination fire/smoke dampers in APPLICATION: Application of sealant between the retaining angles, retaining plates, or sleeve retaining flange and the fire rated wall or floor as Installation instructions Detail drawings for concrete floor installations Detail drawings for timber floor installations Detail drawings for drywall and rigid General product description. Protecta® FR Damper is used to fire proof ventilation ducts which penetrate fire rated constructions such as fire