Abview rohde ngmo1 driver download

Previous Page. Next Page. To maintain this condition and to ensure safe operation, the user must observe all instructions and warnings given in this operating manual. Page 4 Safety Instructions Applicable local or national safety regulations Equipment returned or sent in for repair must be and rules for the prevention of accidents must packed in the original packing or in packing with be observed in all work performed. Page 8: Version 4. Page 9: Operator Information Power Supplies, such differences will be specially emphasized.

The designation NGMO is used wherever the description applies for all versions. If you use this manual for a NGMO1: Just ignore all descriptions and specifications which belong to the channel B of the power supply. However, it is impossible to design hazard-free electrical equipment.

In order to guarantee a sufficient level of safety for personnel working with the Power Supply NGMO, safety regulations must be observed. After unpacking the unit from the ship- ping carton, check for any obvious signs of physical damage that may have occured in transit.

Remove any protective film over the screen. Report any damage to the shipping agent immediately. Page Fig. Page Operation Fig. Operation elements for channel B must in this case be ignored. A menu need not necessarily have submenus. This makes it easier for software deve- lopers to verify that their software is running correctly. Enter exact Resistor value: 3x. Known 3.

Enter exact Resistor value: 3xxx. Remove cal. Enter new CAL. Enter the Date. Use the variation knob and the arrow keys to enter the current date. Calibration success- fully completed! The calibration procedure must be repeated for the other channel NGMO2 only. This can be done in the following way.

Connect calibration adapter to output terminal B. Channel B. Select Menu Item B Repeat all the other steps listed above. If the calibration entry ID is lost, it is possible to set the ID to zero.

The following procedure describes how to enter 0 as the entry ID for new access to the calibration mode. Remove the four screws in the rear feet of the NGMO. Remove the main shielding. The next steps expose you to hazardous voltages. Proceed with care. Observe the relevant safety regulations relating to the operation of electrical devices. Locate the two jumper pins on the bottom circuit board of the NGMO.

Short these two pins using a standard jumper. Apply mains power to the NGMO and switch on the device. Really set cal. Any other key aborts this function. Remove the calibration entry ID jumper. Switch off the NGMO and remove the power cord.

Replace the main shielding on the device and mount the four feet to the rear of the device. This version is equipped with analog boards A and B. All descriptions and specifications concerning channel B must be ignored.

These service functions are on the one hand used to test the installed interfaces, and on the other to test the following functions and assem- blies and to make the following adjustments:. Apart from that the serial interface parameters must be adapted to the parameters of the controlling computer.

Hyper terminal. All service commands start with the character string: "rus:service These are specific for the service and should therefore be treated confidentially. The following sections specify the additional commands, which were implemented in addition to the standard commands.

Setting, input After replacing the processor board this replacement board must be reprogrammed to the serial number of the unit located on the back of the unit. Quotation marks " must also be entered.

Setting, input After replacing the processor board the device name must be repro- grammed, if the name displayed when switching on does not match the designation on the front panel. Description The following remote commands can be used to test whether the communication between the main computer on the processor board and the two satellite computers on the analog boards works correctly. For this purpose a test number can be transmitted to one of the two satellite computers, which can subsequently be read back in a second step.

Description This test is performed to determine whether all pixels of the LC display can be switched off. After initiating the test the LC display should not show any pixels. The second command interrogation command is used to deter- mine whether the test was successfully completed. The interroga- tion command will keep on returning , until the user either presses the ENTER — key, or any other key on the unit.

User Input: Test: OK! Description This test is performed to determine whether all pixels of the LC display can be switched on. After starting this test the LC-display should show grey blocks with all pixels in place. Description This test enables the user to check whether all keyboard keys and the rotary transducer work correctly. Function test After starting operate the rotary transducer first.

When turning clockwise the numerical value in top right hand corner of the display must increase by 1 with every step of the rotary transducer, and decrease by 1 when turning anti-clockwise. After this all keys must be pressed. When pressing one of the keys again, the corresponding field is displayed again in grey. This interrogation command is used to determine whether the test was successfully completed.

The interrogation command first re- turns If the rotary transducer is turned anti-clockwise and clockwise while all keys are pressed, the value 0 will finally be returned. If no error is present, the returned value of the function should be 0. Description This function is used to test whether the output drivers of the NGMO can be switched off via the Inhibit lines.

The following connections see photo opposite must be available on the NGMO output plug:. Force - with Sense -. Function test Set any output voltages on channels A and B.

Switch both outputs to ON see section 5. The following function switches the test functions off again. The NGMO is again ready for normal use. The list does not show any messages which may occur during normal operation. Display Description of error Defective module. But may also be caused by the processor board. Type of fault Fault diagnose Fault rectification. Disconnect the unit from the mains supply before opening the housing.

The following sections describe the procedures for removing and installing assemblies using the Power Supply NGMO2 as an example. This version is equipped with two analog boards Channel A and Channel B. The instructions for removal and installation apply also for the NGMO1, in which case the removal and installation process is reduced to analog board Channel A.

Unscrew the screws from the rear 1, 2, 3, 4 and pull the housing off to the rear. Pull off plug X 22 for fan A. Unscrew the screws of analog board Y Channel A 12 to Remove the board. Pull off plug X 11 for fan B. Unscrew the screws of analog board Y Channel B 1 to Unscrew the screws on the front panel 1, 2, 3, 4.

Fold the front panel carefully down. Pull off plugs X, X and X 5, 6, 7. Unscrew the screws 8, 9, 10, Unscrew screw 8 from the cooling plate of the LMCT. Unscrew screws 9 to Unscrew the screws on both sides of the rear wall 17 to Fold the rear wall carefully down. Take out the processor board. To remove the fan, disassemble the corresponding analog board as described in section 9. Unscrew the screws for the corresponding fan.

Pull the fan up to remove. Carefully insert the board into the connection on the processor board. Fasten the board with the remaining screws 12 to Connect plug X 22 for fan A. Fasten the board with the remaining screws 1 to Connect plug X 11 for fan B. Insert the keyboard into the front panel 2. Turn in screws 8, 9, 10, Connect plugs X, X and X 5, 6, 7 to the board. Fasten the front panel to the frame using screws 1, 2, 3, 4. To install the processor board you must first remove both analog boards as described in section 9.

Insert the processor board into the frame, align it to the fans and locate it with the screw Fasten the RSplug connection 21, 22 on the rear wall with screws. Fasten the rear wall with screws 17 to 20 to the frame. Fasten the board with the remaining screws 9 to I revived one of my favorite games — Morrowind. Many people use Morrowind Graphics and Sound Overhaul to enhance the game. When I run it, This is my first attempt at modding so I don't really know what I am doing.

Help please? It's an easy fix This mod is outdated, please check the description. Elder Scrolls Morrowind could do with some upgrades - and these fantastic mods are here to help. This video is Outdated and NO Longer supported.

It also changes the locations of one of the frogs that conflicted with several popular Balmora overhauls.