Arctic silver how much to use

EN Deutsch. Choose variant Charge. Easy Application Thanks to its consistency, MX-4 is easy to apply, even for beginners. The video below demonstrates the application technique to avoid air pockets between processors and coolers.

Long-lasting Durability Compared to metal or silicone thermal pastes, you don't have to make any compromises with the MX once applied, it lasts up to 8 years.

Proven quality While the packaging of our thermal paste has changed several times over the years, the composition of the formula has remained the same.

How is it tested? The measuring sensors in the DIE are not very accurate, so we use a laboratory device here. Often the values are stated many times too high and have nothing to do with reality. Just as important as the thermal conductivity value is the minimum layer thickness of a paste at a given contact pressure in order to minimise the temperature difference between CPU and cooler.

General data. Density 2. Width: 41 mm Height: mm Length: 10 mm Weight: 0. Spec Sheet PDF. Compliance Documents.

Technical Documents. Product gallery. Prices incl. VAT plus shipping costs. Add to shopping cart. Customers also bought: Customers also bought:. I recommend this product :. I bought it because I had heard about it on YouTube and if it is known despite its age it is not for nothing. I'm currently using an iK OC 4. Very effective thermal paste, good hold on the processor, performance is good after restarting the PCs. Tested on a laptop and on a tower: I recommend to extend the life of the equipment!

This product is very well suited for gamer use. Replacing the fan's original thermal paste with this one gives better performance. This product is the best of the best. It is certainly the most expensive paste but also the most effective!

I'm not sure how to use this product, but it's a good idea to apply a small amount in the middle of the processor. To buy with eyes closed.

Good accessory, nickel quality, easy to apply the paste I'm very pleased with the quality of the product. For me the efficiency is proven. Yes, certainly, but how can you compare? When you have done the necessary manipulations and everything works well, it seems to me that there is nothing to regret. And then at this price level, there's not much to think about in order to afford the best Customer reviews of the Arctic Silver 5 3.

Give your opinion. Reset filters. Reset Apply. Number of reviews: 2 Average rating: Review automatically translated. Report this review as inappropriate. Is this review helpful for you? Number of reviews: 3 Average rating: Number of reviews: 1 Average rating: Number of reviews: 8 Average rating: Number of reviews: 5 Average rating: 7.

Number of reviews: 2 Average rating: 5. Number of reviews: 27 Average rating: 9. Number of reviews: 17 Average rating: 9. Number of reviews: 55 Average rating: 9. Number of reviews: 11 Average rating: 8. Number of reviews: 35 Average rating: 9. Number of reviews: 9 Average rating: 9. Number of reviews: 18 Average rating: 9. Number of reviews: 2 Average rating: 9. Number of reviews: 24 Average rating: 9. Number of reviews: 14 Average rating: 8. Number of reviews: 7 Average rating: 8.

Number of reviews: 23 Average rating: 9. Number of reviews: 8 Average rating: 8. Number of reviews: 9 Average rating: 8. Number of reviews: 8 Average rating: 9. Number of reviews: 5 Average rating: 9. Number of reviews: 11 Average rating: Number of reviews: 6 Average rating: 9. I just try to get a thin layer on with the tube nozzle tip, using it to spread it around. Then when I put the heatsink on I just twist it and apply pressure. With heat and vibration, most tiny airbubbles will work their way out anyway.

This is the "settling" they talk about. Even coverage is more important than smoothing it out, as it'll smooth on it's own. Too much is obviously bad, but too little is worse. Just try to get a good thin layer over the whole top of the heatsink and you'll be fine.

Just check your temps. Here's a link to show you to place thermal sensors. Jul 2, 17 0 18, 0. This is a ac freezer pro 7. My system is overclocked from 2. I just applied the AC 5 by putting a small line vertically and then putting the heatsink on top.

I took the heatsink off to take a look at the spread, and it covered the cpu perfectly without going over. My only concern is that I may have put a little too much. We'll see. Anyway, my idle temps are the same, but my load temps went from 70 to about I hear that immediately after applying, your temps may spike a little until it settles in.

You think the spike is too much, or will it be fine in a week? PS this is all coretemp not speedfan. I prefer to keep the temps under 70, but as low as possible. Anoobis Splendid. Feb 4, 3, 0 22, 0. You just did something completely unnecessary as the pre-applied Arctic Cooling MX-1 compound on the Freezer 7 Pro works just as good better in many cases on the Freezer Series as AS5 and just as good as AS5 with other heatsinks.

What is the average temperature of the room the unit is in and what kind of airflow does the case have? Your idle temps still seem like they could be improved, but they're still acceptable. Especially air cooling. You should have 3 mm fans, plus an 80mm with that Lian-Li so you should have more than adequate case airflow and I doubt you're using the shroud but if the room is hot you can only expect so much.

I would suggest re-applying the AS5 one more time. You need to completely remove any old thermal paste from both the CPU and the heatsink. I use q-tips, but a lot of people suggest a coffee filter to use to wipe away the old stuff.

I believe wusy uses rubbing alcohol followed by a little turpentine. Moisten the coffee filter or q-tip with the rubbing alcohol and start cleaning the heatsink and CPU off. Repeat with the turpentine. I would also read through the Freezer 7 Pro's instructions on properly mounting the heatsink to make sure it's seated correctly.

If you put on a decent amount of compound regardless of what kind you use, most included pastes today are pretty good , and you have good airflow in your case and a good heatsink with decent stock fan you should be fine as long as you're not OC'ing. A little too much thermal compound is better than too little. It doesn't matter if it squeezes out the sides of the die a bit, it's really not going anywhere, unless you way over applied it. Just make sure the heatsink is in good contact and that your temps are within normal range for the first couple of days and you'll be fine.

Check your temps every now and then for the first few weeks particularly in the first few days, and try some heavy gaming to test it and then again about 8 months or so down the road. For testing, you can just use an application like the graphics demo's off of nVidia's website or something.

I use the Nalu one cuz she's an f'n hot Mermaid. Running this and doing a few other things can really tax your CPU and increase your temps to near max. Feb 24, 4, 0 22, 9. I almost always get hot up here in my loft when that system is on and I'm just glad there's a window and that I'm a guy shirt comes off. As far as not using thermal compound, I wouldn't recommend it, but with a CPU that doesn't put out a ton of heat it is possible.