Why do xbox 360s red ring

If you're using a hand drill, set a wooden block under each hole as you drill it to avoid warping the case. If you're using a drill press as I did there should be a steel pedestal with a hole for the drill bit to pass through, saving the case from serious FUBAR-age.

Have the bit spinning before you push into the center of the hole. Repeat this for all the holes. Make sure there are no burrs left on the holes or shards kicking around in the case afterwards. Bang it around a few times to get them out. The last thing you'd want is to have your die from little pieces of metal shorting it out. So far, we've prepped the heatsinks and the motherboard case for these 5MM screws.

Now we get to make sumthin' of it! With the case sitting flat, fan hole in the back on the right, take note of where you need to stick these screws. Now put the 5x15MM screws in the GPU screwholes, screwheads on the outside, so that they come into the case. Put tape over the heads to keep them from falling back out, as shown in the second photo. This tape is very important so don't take it off until I say so!

Ha ha. Lay the case flat again and all the screws should be poking up at you, as they are in the main photo. Place 3 or 4 5MM washers on each of them, the idea being to get them level with the motherboard standoffs. Use a straightedge to check.

If they come up too short or too high the motherboard will get warped and you won't be fixing anything. Now the fun begins. You gotta get the motherboard back in the case with the goal of getting the screws into those orange holes that the X-Clamp posts went through. All while you try to keep those washers on the screws! If they fall off at any point, you'll have to take the motherboard out, put them back on the screw s , and repeat. So try not to do it, eh?

Tilt the case onto its right side where the hard drive connector would be so that you can reach the screws underneath. Angle the back of the motherboard into the case and push it all the way to the rear of the case. Now, untape one of those rear CPU screws and point it into its hole. Give it a few twists to hold it in place and thread the other one in. Now, while carefully holding the motherboard and those untaped screws, lower the motherboard until more screws hold you up and get them into their holes.

Don't let those washers fall out! When it's all said and done you'll have screws poking through those holes. Tape the heads back to the case so they don't fall out. Now press on the motherboard around the screws. It should be solid at each screw. If not you'll need to get back to those washers and pop another one on.

But if it's all nice and immobile throw two washers onto each GPU screw, one onto each CPU screw, and head to the next step! Now we get to mess with those screws one more time before the tape gets taken off for good. A paper-thin coat will be good. If you're using a silver-based paste, make sure you don't put on a ton because if it gets onto anything the silver's conductivity will mess with the other components. Pick whichever heatsink you wanna put on first.

The easiest way to get this right is to look at the smudge marks on the heatsinks, and match 'em with their processors. When you thread the screws on start each one off lightly, then get them up tightly. Try to get them evenly tightened to avoid having too much pressure on one side of the processor and too little on another. When it's all done right the heatsinks should not move at all. Now we get to test it out! Otherwise you won't be turning it on.

Turn it on without the fans plugged in, checking to see how fast the heatsinks heat up. Getting hot in less than a minute is excellent.

Now plug in the fans and put on that plastic fan shroud. Okay, I did the Arctic Silver thermal clean and replacement idea and still a red dot.

Now I'm trying the DB overheat reset idea again. Hi it's the south bridge that causing the issue. And don't use Arctic silver 5. Not the best pasted everybody thinks it is. Mx-4 is the best stuff to use. Might be one of the Rams too under the heat sink. Jack McKinnon shrek. Hey everyone. I just had the same problem. The Xbox Slim froze about once every 15 minutes for about 30 seconds. I was playing on system link, and there seemed to be no issues. I woke up the next morning and turned on the console.

It lit green for a second and then went constant red. Every time I restarted it it went red after half a second. I fully dismantled the machine and took off the heat sink, and heated the processor up to about degrees With a hairdryer. I tested it and the light was then green It overheated quickly because the fan and heat sink were off.

I have fully reassembled the machine and it works great - no red lights. It may have started working because I readjusted all the connections inside the box e. Optical drive, hard drive ect. I didn't find anything super helpful on the internet, so I hope this helps.

Josh M jm Try this first make sure you have no flash drives attached to any of the USB ports if you do remove them and second make sure to reseat the hard drive if you have one by removing then place it back in again now start up the Xbox If still red insert a game disk close the tray now shut off and now turn it on again that should fix it something about the game in first and no flash drives before starting usually does the trick.

Fix Your Stuff Community Store. Back Answers Index. Alex R Rep: 2 2 1. View the answer I have this problem too Subscribed to new answers. Is this a good question? Yes No. Voted Undo. Score Chosen Solution. Was this answer helpful? Finatic Rep: 37 2. Score 3. It's a refurbished Xbox my lady got for me in April, only had it for about 4months I don't know how to take it aprt and don't wanna mess it up.

Can sum one help me solve my problem? I got this xbox sl8m from my uncle When I switch it on,the xbox shows a red light and wouldn't turn on Some one please give me a solution Please please. Donte Beachem Rep: 25 1. Regardless of how good the games were on the original Xbox, it was built like a tank and had the looks to match.

So then the engineering team goes and puts things in the shell. More clearly: Microsoft designed the look of the Xbox and then figured out how to fit the console's guts inside, which can be risky.

Though game consoles are designed to be pretty enough for a living room home theater, their design is also based on heat management. These things are computers. If you pack a computer in a tight box, it's far more likely to overheat. Before selling the Xbox to the public, Microsoft had run the console through various tests, from heat to longevity to cold to movement, and plenty of others. The Red Ring of Death problem was apparently something they didn't come across.

It was only when consoles started coming in as returns that Microsoft began to see the scope of the issue. It wasn't until the release of the remodeled Xbox "S" model in that the console was really fixed, despite years of attempts with behind-the-scenes chip changes.

Amazingly, despite all the problems, the Xbox remained a massive success throughout. For you. This article has a few issues that need fixing. It may contain incorrect information or be formatted in a messy way. You can help Xbox Wiki by cleaning the article up and making sure it follows the edit poilcies.

The Red Ring of Death is when three flashing red lights around the Xbox power button instead of the one to four green lights indicating normal operation represent an internal problem that requires service. Warning signs may include freeze-ups, graphical problems in the middle of gameplay, such as checkerboard or pinstripe patterns on the screen, and sound errors, and the console only responds to pressing the power button to turn it off.

These events may happen once or several times until the hardware failure occurs, or not at all. If the console freezes occasionally, the error will not necessarily follow. The technical problems seem to affect some generations of consoles more than others.

Xenon or Zephyr. This error code is usually caused by failure of one or more hardware components, although it can indicate that the console is not receiving enough power from the power supply, which can either be due to a faulty power supply or if the power supply cable is not fully inserted into the console.