Ego owners manual

->>>> Click Here to Download <<<<<<<-

Your mower has built-in overload circuit protection. When the mower is overloaded, the motor will stop and the power indicator on the mower will flash orange. Remove the battery pack from the mower. Check to see if grass has collected beneath the deck and clear it if necessary, then install the battery and restart the mower. The battery pack will generate heat during operation.

The heat dissipates more slowly in hot weather. The power indicator on the mower will shine orange and the LED on the battery will flash orange.

Make sure to check the sharpness of the blade before mowing. Verify that the lawn is free of stones, sticks, wires, and other objects which could damage the lawn mower or motor. Such objects could be accidentally thrown by the mower in any direction and could cause serious personal injury to the operator and to others. Thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower.

Excessive vibration of the mower during operation is an indication of damage. The unit should be promptly inspected and repaired. When cutting thick grass, reduce your walking speed in order to allow for a more effective cut and a proper discharge of the clippings.

To maintain a healthy lawn, cut off only one-third or less of the total length of the grass. Mow across the face of a slope and never up and down. WARNING: Inspect the area where the mower is to be used and remove all stones, sticks, wire and other debris that might be thrown by the rotating blade. Release the switch to turn off the mower blade rotation when crossing any graveled areas; stones can be thrown by a rotating blade. Set the mower to the highest cutting height when mowing on uneven ground or in tall growth.

For effective mulching, do not cut wet grass; it tends to stick to the underside of the deck, preventing the proper mulching of grass clippings. The best time to mow grass is in the late afternoon, when the grass is dry and the newly cut area will not be exposed to direct sunlight.

If the grass is overgrown, it may be necessary to increase the cut height to make it easier to mow and to prevent overloading the motor. Slow your cutting pace in tall or thick grass conditions. For mulching extremely thick or tall grass, it is advisable to first cut at a high cut-height setting, and then re-cut to the final cut height.

Otherwise, make narrower cuts and mow slowly. WARNING: To avoid serious personal injury, always remove the battery pack from the mower before cleaning or performing any maintenance. Use of any other parts may create a hazard or cause product damage. To ensure safety and reliability, all repairs should be performed by a qualified service technician. The underside of mower deck should be cleaned after each use, as grass clippings, leaves, dirt and other debris will accumulate.

This accumulation is undesirable, as it will promote rust and corrosion. Remove any build-up of grass and leaves on or around the drive shaft only LMSP and motor fan do not use water. Wipe the mower clean with a damp cloth. WARNING: Always protect your hands by wearing heavy gloves or wrapping the cutting edges with rags or other materials when performing any maintenance on the mower blade. Always remove the battery pack when servicing or transporting the mower.

Stop the motor; remove the battery pack from the mower. Turn the mower on its side. While wearing protective gloves, place a metal rod e. NOTICE: If the bolt rotates with the motor shaft when loosening the bolt, turn the fan by hand to align the through holes in the fan with the holes in the blade, and place another metal rod e. Stabilizer 2. While wearing protective gloves, remove the bolt, outer flange and the blade Fig. Mount the inner flange to the fan Fig.

Mount the fan and the inner flange onto the motor shaft with the fan blade towards the deck Fig. Align the outer flange with the shaft and assemble it in place. Mount the bolt into the shaft and turn it clockwise by hand to pre tighten it. While still wearing protective gloves, hold the blade with one hand and turn the fan with the other hand to align the holes in the blade with the through holes in the inner flange Fig. Place a metal rod e.

Place another metal rod e. The recommended torque for the blade bolt is ft-lb Nm. Sharpening the blade twice during a mowing season is usually sufficient under normal circumstances.

Sand causes the blade to dull quickly; if your lawn has sandy soil, more frequent sharpening may be required. Sharpen the cutting edges on both ends of the blade, removing an equal amount of material from each end. Secure the blade in a vise Fig. Wear proper eye protection and gloves and be careful not to cut yourself.

Carefully file the cutting edges of the blade with a fine tooth file or sharpening stone, maintaining the original cutting edge angle. To check the blade balance: clamp a nail or a screw driver with a round shank in the horizontal position. Position the blade so that the nail or round shank of the screwdriver supports the blade through its center hole. If either end of the blade rotates downward, remove some metal from the heavy or lower end until the blade is balanced.

It is balanced when neither end drops Fig. It may cause damage to the mower and could break, causing personal injury. For LM, lubricate the bearings in both the rear and front wheels Fig.

Bearing Bearing. Turn the mower on its side with the upper surface against a wall. Use a flat blade screwdriver to pry the dust cover away from the wheel. Remove the bolt, the worn wheel and the wave washer from the wheel axle. Note: When replacing the rear wheel for the self propelled mower LMSP , remove the drive gear from the worn wheel and assemble to the new wheel with the 3 screws.

Mount the wave washer and the new wheel on the wheel axle. Note that the round recess must face outward. Lock the wheel with the bolt by tightening the bolt clockwise. Mount the dust cover onto the wheel and press it in place. The trailing shield is subject to wear and damage, which could expose moving parts or allow objects to be thrown. For safety protection, frequently check the trailing shield and replace it immediately with only the identical replacement part, listed in this manual.

For self propel mower LMSP, loosen the wheel cover locking screw and remove the screw, spring washer and flat washer in that order, then remove the wheel cover from the wheel shaft Fig. Repeat steps 1 to 3 above the remove the other rear wheel and wheel cover LMSP only. Loosen the locking screw for the trailing shield on both sides; remove the worn trailing shield Fig.

The following steps should be taken in order to prepare the lawn mower for storage. Remove the battery pack from the mower and store it at room temperature in a dry location. Clean the mower as described earlier in the maintenance section. Inspect the blade and replace it or sharpen it if required. Store the mower in a dry, clean location. Do not store it next to corrosive materials, such as fertilizer or rock salt.

Store the mower in a covered, enclosed space, that is cool and dry and out of the reach of children. Do not cover the lawn mower with a solid plastic sheet. Plastic coverings trap moisture around the mower, which causes rust and corrosion. Move the cutting-height adjustment lever toward the front and engage it in the lowest setting setting 1.

Open the handle-locking clamps and fully recess the side. Press and hold the quick-adjust lever with your right hand to release the handle. Gently pivot the handle toward the front of the mower; release the quick-adjust lever and continue to pivot the handle until you hear and feel the lock pin engage in the locked storage position.

Always keep the mower stable and out of the reach of children when it is in the upright position. If possible, lay it flat for storage. Always protect your hands by wearing heavy gloves or wrapping the cutting edges with rags or other materials when performing any maintenance on the mower blade. Defective product will receive free repair. This warranty does not cover the blade, which is a part that can wear out from normal use within the warranty period.

This warranty applies only to the original purchaser from an authorized EGO retailer and may not be transferred. The warranty period for any EGO product or part used for industrial, professional or commercial purpose is one year. This warranty does not cover the damage resulting from modification, alteration or unauthorized repair.

This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse including overloading of the product beyond capacity and immersion in water or other liquid , accidents, neglect or lack of proper installation, and improper maintenance or storage.

This warranty does not cover normal deterioration of the exterior finish, including but not limited to scratches, dents, paint chips, or to any corrosion or discoloring by heat, abrasive and chemical cleaners.

When requesting warranty service, you must present the original dated sales receipt. An authorized service center will be selected to repair the product according to the stated warranty terms.

Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to five years from the date of purchase for outdoor power equipment and three years from date of purchase for battery pack and charger. Chervon North America is not responsible for direct, indirect, incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks and cement and other masonry products, and Arsenic and chromium from chemically-treated lumber.

Safety Alert Indicates a potential personal injury hazard. Eye Protection Always wear safety goggles or safety glasses with side shields and a full face shield when operating this product. Maintain Safety Devices Do not open or remove safety shields while the tool is running. Look Behind While Look down and behind first to avoid tripping when pulling back. Do not operate unless discharge cover or grass and Feet Away bag is in its proper place.

If damaged, replace immediately. Debris Wear safety glasses. Do not mow slopes greater than Hazard 15 degrees.

Be alert and turn the mower off if a child enters the area. Keep clear of the discharge opening at all times.

If you must back the mower away from a wall or obstruction, first look down and behind you to avoid tripping, and then follow these steps: Step back from mower to fully extend your arms.

Be sure you are well balanced with sure footing. Pull the mower back slowly, no more than half way toward you. Repeat these steps as needed. Do not operate the mower while under the influence of alcohol or drugs. Mow only in daylight or good artificial light. Walk, never run while operating. Stop the blade when crossing gravel drives, walks or roads. Do: Mow across the face of slopes; never mow up and down. Do not: Do not mow near drop-offs, ditches or embankments; you could lose your footing or balance.

Do not mow slopes greater than 15 degrees, as shown on the slope gauge. Do not mow on wet grass. Unstable footing could cause slipping. Follow instructions for lubricating and changing accessories. Keep handles dry, clean and free from oil and grease. Maintain or replace safety and instruction labels, as necessary. Mower Weight Without battery pack; Medium load 30 min. Heavy load 20 min. UNPACKING First remove all the accessories from the carton, then grasp the front handle and rear handle at the same time to carefully lift the mower up and out of the carton.

Locked Storage Position 2. Upper Operating Position 4. Middle Operating Position 2 5. NOTE: The motor cannot be started unless: a The side rails are fully extended b Both green handle-locking clamps are securely closed c The handle is locked into one of the three operating positions.

Remove the battery. To reduce the risk of injury, frequently inspect the bag assembly and replace if there are any signs of wear or deterioration. Use only grass bags manufactured for this mower. NOTICE: The mulching insert must be removed in order to install and use the grass bag and must be re-installed when the grass bag is removed. To raise the blade height 1.

To lower the blade height 1. Move the lever toward the front of the mower and engage the lever in the desired cutting-height position on the mower deck. Close the battery cover. NOTE: The motor cannot be started unless: The side rails are fully extended Both green handle-locking clamps are securely closed The handle is locked into one of the three operating positions To start the mower 1.

The mower will start. To stop the mower 1. For example, when you have completed cutting your lawn, you can use the self propel to propel the mower back to your storage location without blade rotation. Visit eReplacementParts. The store will not work correctly in the case when cookies are disabled. Register Your Product. Start Watching. View My Warranty. Contact Us. English Spanish French. Get Updates from the 1 Rated Battery Platform Be the first to know about new products, innovations, and offers.

RXV Electric RXV Elite RXV Gas TXT Electric TXT Elite TXT Gas Search for:. Previous Next. View Larger Image. S6 Express L6. About the Author: Chris Anderson. Chris Anderson has been in the golf cart and electric cart community for over 10 years and has worked with many retail and business to business companies in the industry.