Installing snap together bamboo flooring
->>>> Click Here to Download <<<<<<<-
Coat the back of the nosing with glue and press it into place. Apply glue to the second piece of bamboo and fit into place behind the nosing. Continue until you have glued all pieces to the step. Cover each step on your staircase in this manner. As you go along, you can tap the edges of the boards with a rubber mallet to ensure that they are properly seated. Nail down each board with a finishing nail at each end, 2 inches from each end of the board.
Fill the holes left by the nails with wood putty. By Rochelle Leggett. Talk to our expert! Main Menu. Your Cart 0 Items. Limit of 5 free samples or one shipment per household. Limit of 20 free samples or one shipment per household. Continue Shopping Proceed To Checkout. Click-Lock Strand Woven. Strand Woven. Bamboo Click Lock Flooring. Perfect for DIY'ers, our interlocking bamboo flooring just "clicks" together - no glue, no nails. Some examples of this floor are below. Please remember it is the responsibility of the person installing the floor to determine the suitability of the application, materials, and conditions before beginning the installation.
Please handle, transport, and unload the flooring with care. Bamboo should be stored in a dry place, with at least a four-inch air space under cartons.
Flooring should not be delivered until the building has been closed in with windows and doors in place, and until cement work, plastering, painting, and all other materials are thoroughly dry. It is necessary to acclimate glueless-click bamboo, and best if it is stored in the area where it will be installed at least 48 hours prior to installation. If necessary, you may want to consult with a professional for proper testing and guidance. Moisture levels above Checking for moisture: Use a Delmhorst J-4 or equivalent moisture meter for wood, or a Tramex Concrete Moisture Encounter meter or equivalent for concrete.
You can also use a calcium chloride test for concrete; test results above 3 lbs. Before installation, lay out the flooring where it is to be installed that is, lay the planks down roughly as they will appear after installation , taking care to mix it in a shading pattern pleasing to your eye.
Installer should inspect each plank at this time for finish and quality. Remember that all natural flooring comes in a range of colors and shades.
Our quality control procedures at the factory ensure that very few, if any defective planks are delivered to the consumer. Remove baseboards and undercut door jambs to ensure a quality installation of glueless-click bamboo. Remember to allow room for expansion around the entire perimeter of the flooring. Failure to provide room for expansion will result in installation issues.
Glueless-click bamboo flooring may be installed on, above, or below grade soil level. Care should be taken not to expose the flooring to standing water or liquids for extended periods of time, as it may damage the floor. Because of the versatility of our glueless-click bamboo flooring, it can be installed over virtually any hard surface floor such as wood, vinyl, and even ceramic tile be sure the tiles are firmly attached to the subfloor. Carpet or other textile products will need to be removed prior to installation.
Before beginning the installation, check for squeaks and other loose areas to ensure they are firmly attached. Areas that are loose should be fastened with screws or ring shank nails, as it will not be possible to do this once the flooring is installed.
The subfloor should be clean, free from dirt or other debris, and relatively flat and level. While it may not be critical to be exact, it will provide a more solid base for the flooring which will help to eliminate movement or hollow sounds when walked on.
High spots can be removed by sanding wood or grinding concrete , or the low spots may be filled with an appropriate leveling compound. Due to the popularity of radiant heat and the many systems available; you will need to consult with the manufacturer of the system to ensure that it is compatible with the glueless-click flooring you have selected. Rapid heating or excessive heat may damage the flooring or finish.
If installing glueless-click bamboo on concrete, the concrete should be fully cured 30 — 60 days before beginning preparation for flooring. For both wood and concrete subfloors, the radiant heat should be turned on for approximately one week to ensure excess moisture is removed. Turn the system off for at least 24 before beginning the installation.
After the bamboo flooring is installed, the system may be turned back on. It is important the system be returned to the operating temperature slowly , preferably over 24 — 48 hours. Depending on the type of locking system that comes with your glueless-click bamboo floor, you can install the planks one of two different ways or sometimes both — varies by manufacturer. Move the plank gently up and down while pushing forward.
The plank will then automatically fold into place. You can either insert the tongue into the groove or the groove on to the tongue. The tongue in groove method is most common, and also the easiest. Never force the plank to lay flat, always help it to fold into position. See Diagrams A-1 through A Method B : You can also tap the planks into place with a tapping block and hammer without lifting the planks. The planks should not be tapped together with a single tap.
To avoid damaging the plank, you must tap them together gradually. See Diagrams B-1 and B Select personalised ads. Apply market research to generate audience insights. Measure content performance. Develop and improve products. List of Partners vendors. Featured Video. Read More. Your Privacy Rights. To change or withdraw your consent choices for TheSpruce. At any time, you can update your settings through the "EU Privacy" link at the bottom of any page.
These choices will be signaled globally to our partners and will not affect browsing data. We and our partners process data to: Actively scan device characteristics for identification. I Accept Show Purposes.