Wireless dt-8855 thermometer software

->>>> Click Here to Download <<<<<<<-

Specifically, I'm asking about the four contacts near the bottom of the device Asked by: Tim from Facture Thank you for your interest in our product The output jack of the transmitter base provides a 1 MVdc per degree analog output. Call us at Contact us for detailed inquiries. Volume discounts available Volume Discount Schedule.

Added to Your Shopping Cart. Configuration complete. Please add to cart to keep it or exit the configuration. In stock Product Specs. Product Details. All Models. Rated 1 out of 5 by Lew Harriman from Does NOT project a ring of laser dots This device does not have the key feature that is so clearly shown in the illustration. Date published: Support Materials. M user manual. Compliance Certificates 1. Permanent eye damage will result. Use extreme caution when the laser beam is turned on.

Do not point the laser beam towards highly explosive gases. Keep out of reach of all children. Keep this device away from rain, moisture, splashing and dripping liquids. Visible laser radiation. Do not stare into the beam as eye damage may occur. This device contains a class 2 laser. No user-serviceable parts inside. Avoid brute force when operating the device. Using the device in an unauthorised way will void the warranty. Overview Refer to the drawings on page 2 of this manual. The LCD display [3] shows the current temperature [K].

Use the mode button [6] to scroll through the modes of the device. The mode [J] and corresponding value [H] are shown on the display. To cancel mode selection, pull the measurement trigger [8]. Pushing the mode button [6] after setting the lower alarm limit will start the set-up cycle again.

Their value is reset when a new measurement starts or the thermometer switches off. The battery cover has a hinge at the bottom of the device. Hold the battery cover at the top next to the measurement trigger [8] and gently pull away from the device.

Move this switch to the desired setting. The current setting is indicated [F] in the display. Move this switch to the ON-position for continuous measurement. The current setting is indicated with a lock symbol [E] in the display.

Start measuring by pulling the measurement trigger [8] once. Consider disabling the laser targeting beam in continuous measuring mode to save battery power. To stop and disable lock mode, set the switch [M] back to the OFF-position. Move this switch to the ON-position to enable alarm warnings when high or low alarm limits are exceeded.

Alarm will stop when temperature is back within preset limits. Note that the laser beam is only an aiming aid, be careful when using it. Refer to the safety instructions.

The connector is slotted and can be inserted only one way. Do not force. Use the mode button [6] to go to Tk mode [J] and read the thermocouple temperature [H].

Use the mode button [6] to go to LOG mode [J] and use the up [5] or down [4] button to scroll through the memory. Connect the thermocouple and attach it to the surface. Pull and hold the measurement trigger [8] consider placing the meter in lock mode [M]. Point the IR sensor [1] towards the surface, close to the location of the thermocouple. When Tk and IR measurements are identical and stable, press the up [5] or down [4] button. The measured emissivity [C] is indicated [D] and normal measurement can be resumed.

Place the connector pins at the front of grip [9] first, then tilt down until the meter snaps in place. To remove, lift the back up first. Screw the tripod into the bottom of the transmitter stand and extend the legs of the tripod to set the preferred height.

Position the head and use the screw on the side to secure it. A COM-port was assigned to this bridge controller; it is mentioned between brackets at the end of the line. Remember this number as it is needed to configure the software. Double click left on the device name to see more details. The application opens.

Consider placing the meter in lock mode [M] for easy handling. The red status LED on the receiver lights up. Place the connector pins at the front of grip [9] first, than tilt down until the meter snaps in place.

When the thermometer is in SCAN mode, the status LEDs of both transmitter and receiver start blinking in sync, indicating there is communication. Data will be shown in the data window [n]. Set the sample time [t], this is the time the software waits between 2 interrogations of the thermometer. Set the lower [o] and higher [p] time limits. These are indicated by a horizontal line on the selected temperature. When the temperature crosses these lines, the graph will turn red see example below.

The file format is. Data which is not saved prior to closing the application is lost. Useful information Working principle The Infra Red sensor of the unit detects energy that is emitted, reflected and transmitted by a surface. This energy is focussed onto a detector that converts this information into a temperature reading. The laser beam is only used for aiming purposes. Ambient temperature The thermometer automatically compensates ambient temperature conditions. Allow the thermometer to stabilise to ambient temperature for at least 30 minutes for accurate measurements.

PC Interface Software with manual - 32mb. Programmable relays. Q Programmer software for programmable stepper drives. Si Programmer software and manual. Software for CN Software for Dpi Series. Software for FDT Series ultrasonic flow meters. Data Logger. Software for Handheld Thermal Imager with Smartphone integration. Software for RD - Paperless universal inputs Recorder. Software for RD Software for SP Software for the OSXL Software for Universal Verbalizer.

Sofware for DP