Ameba Ownd

アプリで簡単、無料ホームページ作成

Install brick patio floor

2022.01.14 16:46


->>>> Click Here to Download <<<<<<<-





















After positioning all of the bricks, apply additional sand in the spaces between them. I have found it easiest to pour sand in a small area before using a push broom to move the sand over all the openings. Repeat the process until the gaps between the bricks and borders are evenly filled and level.


Disclosure: BobVila. You agree that BobVila. All rights reserved. Expert advice from Bob Vila, the most trusted name in home improvement, home remodeling, home repair, and DIY.


More From Bob Vila. How To: Build a Paver Patio. Your comments and sharing are greatly appreciated! Site message including reference link shown here. Quantity includes typical waste overage, material for repair and local delivery. Clean and complete minor repairs to structure of existing concrete surface. Layout pattern. Set brick pavers in mortar.


Includes planning, equipment and material acquisition, area preparation and protection, setup and cleanup. Daily rental. Consumables extra. For sidewalks, slabs and driveways. The soil must be firmly in place if it is to support the weight of the patio.


If you are using a manual tamper this process can take some time, but it cannot be rushed. Lay down the gravel or crushed rock. It should be spread out up to a depth of four inches. Make sure to maintain the integrity of the slope you may have created earlier. The rock should also be tamped into place to solidify the foundation of the patio. Cover the rock or soil with the landscaping fabric. This should prevent the growth of weeds. Install the border. If you are not digging deep or laying down a rock layer, you may want to do this immediately following the excavation.


It may be desirable to screw the boards together if lumber is being used as the border. The added stability will help hold the patio in shape. If pavers are being used, stand them up in the trench you dug for the edge and tap them into place. Try to fit them as snugly together as you can. Whether using boards or pavers, make sure that your border is installed at the desired angle or, more likely, with no angle by using a level.


Partially fill in the site with sand and then screed it level. One to two inches are considered a reasonable amount, and it is no longer desirable to maintain the slope you may have created earlier. It is now necessary to level off the sand with a screed which is a term used for any object used to scrape or level. Tamp down the sand. Be careful not to disturb the level surface that you have created. Lay the pavers into place. Press them into the sand as you lay them. Lay the pavers as closely together as you can and use a rubber mallet to seat them into the sand.


Use a small level to check the bricks in 2 directions, and use at least a 6-foot level for a drainage slope. Spread a layer of sand over the bricks. Carefully sweep the sand to fill in the cracks between the bricks and along the edge. Only do this after all the bricks are in place. If some of the bricks aren't in yet, sweeping the sand into unstable joints will cause the bricks to move around. Gently spray the pavers with water.


Use only a small amount of water, as using too much will wash the sand away and loosen the joints. This will allow the material to settle between the bricks. Your project is now complete. You can also sweep the sand away rather than spraying water. Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow. Scott Johnson. Support wikiHow by unlocking this expert answer.


Not Helpful 1 Helpful 0. I'm using surplus bricks with scalloped edge. Are there any concerns I should watch out for? Anthony "TC" Williams. Not Helpful 0 Helpful 1. Not Helpful 4 Helpful 9. But if you have a lot of cuts to make, it's worth it to rent a brick splitter or a masonry wet saw for half a day.


These tools make much faster, cleaner cuts than a hammer or handheld saw. The best blade to use for saw cuts is a diamond blade. Alternatively, you can use an abrasive blade, but it may wear down quickly and won't cut as cleanly. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights.


Measure content performance. Develop and improve products. List of Partners vendors. Project Overview. Why We Use Paving Bricks. Tip If clay bricks are kiln-fired, they are harder than concrete. Featured Video. Materials Paving bricks Brick patio edging Compactible gravel Landscape fabric Sand pound bag polymeric sand.


Mark the Patio Edges Use stakes and mason's line to create layout lines for the patio.