Wagner 9150 owners manual

All information given for the cart model applies to the stand model except where indicated. Injection can lead to amputation. Position the handle against the cart so that the holes in the handle line up with the holes in Page 6 This column contains instructions that will be repeated throughout this manual. Plug the sprayer into a heavy duty grounded extension cord. Refer to Important Electrical Information, page 3.

Place a full container of paint underneath the suction tube. Secure the return tube into a waste container. If any of these occur, it will reduce the flow of paint, making your spray pattern poor, or paint will fail to spray from the gun. When using oil-based paints, use mineral spirits. Remove spray gun from the paint hose using adjustable wrenches. Remove filter from spray gun refer to Cleaning the Spray Gun Filter, page 9.

If using materials that are oil-based, follow the long-term storage steps. Lock the spray gun off. Switch the pump OFF, and unplug the sprayer. Follow the cleaning procedures in this manual. The following list indicates the available repair kits for the parts replaced by each kit. After performing the pressure relief procedure, be sure to unplug the unit before servicing or adjusting.

The sprayer does not start. The sprayer is not plugged in. D,, D, Marque y retire el papel tapiz, o. Important Safety Information Read all safety information before operating the equipment.

Save these instructions To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual.

Hazard: Fire. Hazard: Electrical Shock. May cause severe injury. Hazard: General. Grounding Instructions This product should be grounded. Extension Cords Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the product. Should a problem occur with the steamer, contact Wagner Technical Service.

Product Registration Register your product online at www. English 2. Call Wagner Technical Service at: Register your product online at: www. Never use more than two extensions when using the steamer. Never attach extensions or accessories while unit is emitting steam. If using an extension, attach the accessory to the extension. Push the button on the handle a and attach the steam plate, extensions, or cleaning accessory to the trigger mechanism. If using the jet nozzle, assemble nozzle brush to the jet nozzle, line up the notch in the jet nozzle the brush onto the nozzle.

Flip up filler cap lid and carefully unscrew filler cap. Replace fill cap and shut filler cap lid when filled with desired amount. English 4. Usage Start Before you begin: do not leave steam plate unattended, or face down on any surfaces.

The spray handle may become warm to the touch during usage. Using the trigger 1 1. You can control the flow of steam from the accessory by activating the trigger. The trigger will also relieve any built-up pressure remaining in the system after the steamer has been shut off. Note: Just turning the power OFF does not relieve steam pressure. During cool down, treat the unit as if it is under pressure. Always activate the trigger before removing the fill cap. Shut the unit OFF. Unplug power cord.

Once unit has sufficiently cooled, Activate trigger until all pressure Allow steamer to cool for at least repeat steps in Setup to has been released. Wallpaper removal 1 2 SEC. The perforations will allow the steam to penetrate the wallpaper. Always test a small area of the material, preferably an area that is normally out of view. See below for more information on steam cleaning.

Pressurized steam may bounce back off cleaning surface. Using the Cleaning Accessories: The accessories are excellent tools for cleaning a variety of surfaces. The Large Cleaning Brush a The large cleaning brush and a towel can be used to clean large, solid areas or upholstery. It can be used on surfaces such as ceramic, stone, parquet, marble, linoleum and carpet see Steam Cleaning Tips , b right, before cleaning. The rubber blade can be used to scrape away dirt and other particles as steam is c applied.

The Extensions c The extensions can be used for floor cleaning and to help you reach into higher or harder to d reach areas. The Jet Nozzle with Brush d The jet nozzle is recommended for steam cleaning smaller, harder to reach areas. English 6. You can only view or download manuals with. Sign Up and get 5 for free.

Upload your files to the site. Keep effective footing and balance at all times. Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A 14 or 12 gauge cord is recommended see chart below. If an extension cord is to be used outdoors, it must be marked with the suffix W-A after the cord type designation.

For example, a designation of SJTW-A would indicate that the cord would be appropriate for outdoor use. Do not use more than feet of spray hose. If you need to spray further than feet from your power source, use more extension cord, not more spray hose. The cause of the overload should be corrected before restarting. Take unit to Service Center. This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. Improper installation of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the green grounding wire to either flat blade terminal. The wire with insulation having a green outer surface with or without yellow stripes is the grounding wire and must be connected to the grounding pin. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if you are in doubt as to whether the product is properly grounded.

Do not modify the plug provided. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. This product is for use on a nominal volt circuit and has a grounding plug that looks like the plug illustrated below. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Grounded Outlet. Grounding Pin. If you experience problems with your sprayer at any time during assembly, operation, or cleanup, please refer to the Troubleshooting section of this manual page 22 , or call customer.

Suction tube. Fluid is drawn through the suction tube into the pump. Fluid Section. A piston in the fluid section moves up and down to create the suction that draws fluid through the suction tube. Spray Gun. The spray gun controls the delivery of the fluid being pumped. Spray Hose. The spray hose connects the gun to the pump.

Return Tube. Pump Cleaning Adapter. The adapter allows you to attach a garden hose to the suction tube for easy cleanup latex materials only. Pressure Control Dial. The pressure control dial regulates the amount of force the pump uses to push the fluid. Pusher Stem. The pusher stem is designed to keep the inlet valve open and from sticking due to dried materials. This pump is available in two models: a stand model S and cart models , shown below, and Some of the graphics in this manual may not exactly match your sprayer and spray gun.

All information and instructions given in this manual applies to all models except where noted. Hose bracket. If you have one of the cart models , , or , follow these assembly instructions. If you have the model S sprayer, skip to item 4, below.

Twist the knobs on either side of the handle counterclockwise to unlock the handle. Pull the handle out fully, and turn knobs clockwise to lock into place. Insert the ends of the hose bracket into the holes of the handle as shown.

Attach the pail bracket. Line up the holes in the bracket with the holes in the sprayer. Thread the high pressure hose to the spray hose port. Tighten with an adjustable wrench. Thread the other end of the hose to the spray gun. Hold the gun with one adjustable wrench, and tighten the hose nut with the other. Before you begin - This section contains instructions that will be repeated throughout this manual.

To lock the gun, turn the trigger lock forward and slightly down until it stops. Plug the power cord into a grounded outlet or heavy duty grounded extension cord. Plug in the extension cord. Refer to Important Electrical Information, page 3. Lock the spray gun off see directions above. Unlock the spray gun and trigger spray gun into the side of the material bucket.