Installing decorative ceiling tile

Decorative Ceiling Tiles Installation Instructions Do you want to start installing ceiling tiles in a particular room in your home?

Here, you can find plenty of DIY resources for learning how to install ceiling tiles. Only Decorative Ceiling Tiles is your one-stop shop for both advice and the very best in quality ceiling tile materials.

We have tiles to match every budget and tiles that will give you a look that you have always wanted. Use our calculator and you can buy the perfect amount of tiles. Method 1. Clean the ceiling. If the ceiling isn't very dirty, simply use a broom covered with a tee-shirt to dust away any dirt. If your ceiling is dirty or greasy, use a sponge to scrub one small section at a time using an all-purpose cleaner. A clean surface will make your tiles stick more effectively.

You may have trouble attaching them if the ceiling is dirty or has peeling paint. If your ceiling is very greasy, wash it using a mixture of 1 cup ammonia and half a gallon of water. Measure the square footage of the room. To do this, use a measuring tape and record how long the ceiling is. Then measure how wide the ceiling is. Multiply these two numbers to get your square footage. Determine how many tiles you need. You'll need to figure the square footage of each tile.

Again, multiply the length times the width to get the tile's measurement. Then divide the square footage of the ceiling by the square footage of one tile. This will tell you how many tiles you'll need. If the square footage for your room is , divide it by 4. You'll need at least 45 tiles. Always buy 15 percent more tiles than you think you'll need. That way, if you need to cut tiles or make a mistake, you'll have plenty to complete the job.

Remove any fixtures or vents. Unscrew any light fixtures, fans, or air vent covers. This will allow you to easily measure tiles and install them without damaging fixtures. You'll probably want to use a flat-head or Phillips screwdriver to remove fixtures. This is also a good time to give fixtures and vents a quick clean. Method 2. Use chalk lines to find the center of the room.

Measure halfway across each wall in opposite directions, using the length and width measurements you made for the ceiling. Have someone hold the chalk line or reel while you walk to the opposite end of the room. Snap the chalk against the ceiling. Rotate 90 degrees and do the same for the two opposite walls. When completed, you should have 2 straight lines that cross each other in the center of the room. This will be your starting point for laying tiles.

Apply cement or adhesive to your tiles. Use a foam brush or putty knife to spread adhesive on the back of your tiles. Spread adhesive to the four corners of the ceiling tile, about 1 inch 2. Check package instructions to determine the correct adhesive or cement for your tile material. Apply whole tiles to the ceiling. Place your first tile in the center of the room, where the two chalk lines meet. Press it firmly against the ceiling, making sure it is level and aligned properly.

Continue to place the tiles by working out from the center until you reach the other side of the room. Use the chalk lines as a guide. Cut tiles for fixtures. When you reach a fixture hole, measure the size and shape of the hole and locate where it will be on the ceiling tile you're preparing to place.

Use those measurements to draw and cut the hole using a straightedge or scissors. Apply glue and place the tile on the ceiling where the fixture will be. Do a dry run and test your cut before adhering it to the ceiling. Simply hold your cut tile up over the hole, making sure the hole is completely visible. This way you'll be able to easily reinstall the fixture. Measure and cut edge tiles.

By the time you've almost completed tiling your ceiling, you may notice that you're near the edges and that the tiles will not entirely fit. You'll need to measure the exact size of tile for the edges. Then use a straight edge to cut the tile, apply glue, and press the edge tile against the ceiling. Repeat this around all the edges. Additionally, a drop-in ceiling system might be the best choice for your home renovation project if you live in an older house where the framing has settled over time.

In this case, a drop-in system enables the installation of a level ceiling without a lot of costly framing corrections. Shop around and compare prices and ceiling options. You will quickly see that there are many advantages to a drop-in ceiling. Once you are ready to buy your tiles, and especially if you plan on doing the remodeling work yourself, your biggest question might be whether a decorative drop-in ceiling tile installation is a DIY-friendly home project.

These videos along with these simple instructions should help you successfully complete your dropped-ceiling installation. You now have your prep work done and are ready to begin installing the grid system that will support the decorative ceiling tiles. If you did the prep work correctly, these steps should be quick and easy:. Special note — Some grid support systems use a main T every 4 feet rather than every 2 feet. These systems will have a 4-foot secondary T that spans the distance between the main tees.

The cross Ts are then used to divide the gaps between the main and secondary Ts into 2-foot squares for your tiles. If you have this type of system, follow the above directions for installing the main Ts, and then snap the secondary and cross Ts into place.

There should be a hanger wire everywhere a secondary T connects to a main T. Congratulations — you have now installed a drop-in decorative tile ceiling!

Home Drop Ceiling Tiles Installation Instructions Drop Ceiling Tiles Installation Instructions Drop ceiling Installation Instructions While drywall is the finish material most often found on the ceilings of homes, drop-in ceilings are usually the first choice of commercial contractors for professional offices, restaurants, and retail spaces. Lengths can vary depending on your wall covering, but they should be long enough to provide a good anchor into solid framing Laser level — this is optional, but can make the job go much quicker.

They are available at most tool rental establishments or can be purchased at home improvement stores. Drop-in decorative ceiling tiles — available from Decorative Ceiling Tiles in numerous styles and finishes. Make sure you order tiles designed for drop-in applications. At the very least, move everything to one side of the room while working on the other side. Remove loose ceiling debris— If you have a popcorn or textured ceiling, scrape away any loose debris.

Find the room center — If you have a light fixture or ceiling fan in the room that looks as if it is in the middle, use this as your center. Otherwise, pull your string line diagonally across the room from corner to corner, and the location at which the two lines cross should be the center.