Apc ups 700 user manual

Is your question not listed? S ma ll spa rks m ay occu r du ring b atte ry. The outlet. No t e: Pri or to fi rst u se, cha rge th e Ba ck-U P S for a t l east 16 ho urs to en su re suffici ent run ti me. The u ni t is charg ing. Conn ec t a com pu ter ,. No te tha t o ne of thes e outl ets is the Ma ster o ut let.

Co n trolled O utl e ts— C o nn ect p e riphe ral de vic es. Su r ge Protec ti on— T hes e outl ets provi de fu ll- tim e pro tect ion fro m. C onne ct a p rin ter, fax m a chi ne, scan ner, or oth er. No te tha t i f the p ow er-sa ving feat ur e is en a bled, th ree of the s e. Ci rcuit Brea k er —Pus h to re-se t the circ u it br eak er.

Note : Do not. Ask a question. Rick, No comments 0. Su r ge Protec ti on— T hes e outl ets provi de fu ll- tim e pro tect ion fro m. C onne ct a p rin ter, fax m a chi ne, scan ner, or oth er.

No te tha t i f the p ow er-sa ving feat ur e is en a bled, th ree of the s e. Ci rcuit Brea k er —Pus h to re-se t the circ u it br eak er. Note : Do not. Ask a question. Related product manuals. See section 6. See section 5. It also displays the voltage of the utility line.

The on-battery LED comes on when the unit is supplying battery power to the loads. Press the off button to turn off the unit and the load. The loads receive normal power. The on-line LED comes on when the unit is supplying utility power to the loads. The load display shows the power being drawn by the load.

Use the computer interface port for unit monitoring and control. See section 7. The configuration LED indicates the voltage sensitivity setting and the low battery warning interval. The site wiring fault indicator comes on when the unit is connected to an improperly wired AC power outlet. See section 4. The center plunger of the circuit breakers extend when tripped. The center plunger of the circuit breaker extends when tripped.

Use the transient voltage surge suppression TVSS ground connector for the ground leads of telephone or network line protectors. See the table below for input power connectors on VA and VA models. Optional output power receptacle kits are available from the factory for the VA and VA models.

See your dealer or call the number at the front of this manual for more information. Optional accessories can be installed in the accessory slot. Use the battery pack connector to connect the optional external battery pack VA model only. To obtain warranty coverage fill out and return the warranty registration card now. Inspect the unit upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.

Install the unit in a protected area with adequate air flow and free of excessive dust. Do not operate the unit where the temperature and humidity is outside the specified limits. Allow the unit to come to room temperature before continuing.

This unit provides high performance power line protection to the loads. There are, however, other potential entry points for damaging surges in information systems.

These other entry points must be considered in developing a comprehensive system protection strategy. Contact your dealer or call the number in the front of this manual for information on a complete set of related products designed to accomplish total system protection. Plug all power protection and information system equipment into the same branch where.

Some accessories connect to the computer interface DB-9 port, while others install in the accessory slot. See the literature accompanying the accessory to determine proper installation. The screws holding the slot cover are 2 Phillips head type. Connect the optional battery pack VA model only according to the instructions with the battery pack. Plug the unit into a two-pole, three-wire, grounding receptacle only.

Avoid using extension cords and adapter plugs. The unit charges its battery whenever it is connected to utility power. For best results, charge the battery for 2. It is acceptable to use the unit without first charging the battery, but on-battery run time may be reduced until the battery charges. Plug the loads into the output connectors on the rear of the unit.

Caution: Do not connect a laser printer to the unit along with other computer equipment unless the unit is rated VA or higher. A laser printer periodically draws significantly more power than when idle, and may overload the unit. Verify that the unit can support the loads when the printer is in full operation printing. Test the system with all loads operating to make sure that the unit is not overloaded. After plugging in the loads and the unit, check the site wiring fault indicator on the rear panel.

See section 3. It lights if the unit is plugged into an improperly wired AC power outlet. Wiring faults detected include missing ground, hot-neutral polarity reversal, and overloaded neutral circuit. Caution: If the unit indicates a site wiring fault, get a qualified electrician to correct the building wiring. The unit features a TVSS connector for connecting the ground lead on transient voltage surge-sup- pression TVSS devices such as telephone and network line protectors.

Tighten the screw to secure the lead. The loads are immediately powered while the unit beeps and performs a self-test. Note: The unit is on the internal processor is operating whenever it is plugged in and utility voltage is present. Even when switched off the unit maintains the battery charge and will respond to commands received through the computer interface port and the accessory slot.

Use the self-test to verify both the operation of the unit and the condition of the battery.